SilverStone Grandia GD07 Przewodnik Instalacji

GD07

98lnstallation Guide9Install 2.5” hard drives into the drive cage.Установите 3,5-дюймовые жесткие диски в кронштейн для жестких дисков.Bauen Sie 3,5-Z

1010lnstallation GuideORInstall 3.5" hard drives into the drive cage, hard drives can be installed either facing left or right depending on your

11In order to maximize interior space usage, the right of the main hard drive cage does not have any anti-vibration mechanism and only supports standa

121213Please connect all SATA cables to the motherboard as required by your system.Подключите к материнской плате все необходимые кабели SATA (или IDE

1314lnstallation Guide15Remove the 5.25” drive bay covers as shown.Снимите заглушки отсеков 5,25 дюйма, как показано на рисунке.Entfernen Sie die 5,25

141617Push the optical drive or 5.25" device into the 5.25" drive bay.Установите оптический дисковод или 5,25-дюймовое устройство в отсек дл

15We recommend connecting all devices with 90 degree SATA and power cables especially the rightmost 3.5" hard drive, the maximum height of the ha

1619Place the top cover back onto the case and secure with screws.Установите на место верхнюю крышку корпуса и закрепите ее тремя шурупами.Setzen Sie

17Power switch and reset switch installation guide: Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector” or “System P

18Front I/O connector guideBelow are the front I/O connectors pin definition, please also check your motherboard manual to cross reference with mother

1Installation and system optimization guide:The following manual and guides were carefully prepared by the SilverStone engineering team to help you ma

19Component size limitationsThe GD07 was designed to be as small as possible while maximizing interior space usage, please refer to the following guid

20The distance between the base of the main hard drive bracket and the motherboard is 32.7mm. (the clearance height for the CPU cooler under the main

21Component size limitationsThe optical drive area on the right of the main hard drive bracket has a clearance height of 129.7mm when no optical drive

22Dual CPU motherboard’s CPU’s are normally positioned on either side of the motherboard, we suggest you to use the motherboard with the CPU placed on

23Component size limitationsA. Depth limitation: The distance between the PSU and the 5.25” drive bays to the left of the main hard drive bracket is l

24A. Ограничение по глубине: Расстояние между блоком питания и отсеками 5,25-дюймовыми дисководами слева от кронштейна основного жесткого диска ограни

25Component size limitationsIf there are no hard drives installed in front of the graphic card, the maximum length for the graphic card is 13.6”.If ha

26Inside the main hard drive bracket there seven sets of mounting holes to secure the hard drives, you can install up to four hard drives. Default pos

27Component size limitationsНа кронштейне основного жесткого диска имеется ряд установочных отверстий для крепления жестких дисков (можно установить д

28If the graphic card is installed in the first expansion slot, we recommend you to install the first hard drive with its IC board facing left using t

GD07Amazing home theater server case with incredible storage capacity and security2MaterialModelMotherboardDrive BayCooling SystemExpansion S

29Component size limitationsMotherboard compatibility and fan limitation:GD07 supports up to SSI-EEB (Extended ATX motherboard), below is a table of r

30The distance between the motherboard and fan are sufficient for traditional SATA cables, but we still recommend to use SATA cables with a smaller co

31Component size limitationsA: The maximum clearance between the optical drive and the inner part of the front door is 10mm.B: The maximum size of a U

32If you are installing a tower-style CPU cooler, we recommend that the CPU fan blows rearward to work with GD07’s overall airflow.Falls Sie einen tow

33Recommended cooling device setup and selectionWhen choosing a graphics card, we recommend models that have fan blowing exhaust air to the rear slot,

34Power cord-use clips to secure the cord in front of the power supply unit.Cable routingЗажимы кабеля питания для крепления кабеля блока питания.Netz

35Recommended cooling device setup and selectionBy default, the GD07 includes 3 fans to meet most cooling requirements. If you like to add more fans t

36GD07’s positive air pressure design is an effective configuration that will reduce dust buildup inside the case. Small air particles or lint will a

37Recommended cooling device setup and selectionRight side filter can be removed. Фильтр с правой стороны можно убрать.Rechter Filter kann entfernt we

38Installation of a slot device or short expansion card such as extra motherboard I/O, fan controller, or daughter board (e.g. ASUS Xonar HDAV1.3), Pl

3TOP COVER5.25” DRIVE BAY x 25.25” DRIVE BAY x 23.5” DRIVE BAY x 42.5” DRIVE BAY x 212025 FAN x 2BOTTOM SIDE FILTER x 23.5” DRIVE BAY x 1RIGHT SIDE FI

39Recommended cooling device setup and selectionTo remove bottom fans, remove the drive bracket and bottom filters, then loosen the fan screws.Для изв

40A Kensington lock can be used on the GD07 to prevent removal of the entire system or the top cover.Caution：Before purchasing the lock, please be sur

41Protect your computerWe suggest using the key locks on the front door to protect your hard drive. The optical drive, USB ports, and Reset button wil

42The front door panel contains a power button lock. Please refer to the picture below; when the power button lock is pushed to the right, you will di

43Q&AQ: How to manage cables when the main hard drive bracket is full of hard drives?A: Normal power cables for hard drives are difficult to manag

44Q: found that the GD07 is too large to fit in my home theater cabinet after installing the display output adapter. How can I solve this problem?Q: D

45Q&AA: Please use the adapter cable as a replacement for the display output adaptor. The cable can be bent in any direction to ensure that the GD

46Warranty InformationDuring warranty period, assistance for replacement or exchange of defective components is available at the place of purchase wit

February, 2012NO: G11215360

412Loosen two screws from the rear of the chassis then remove the top cover.Ослабьте два винта на задней панели корпуса и снимите верхнюю крышку.Lösen

5Insert the power supply from the top, if the power supply has a built-in 120mm fan or larger, we recommend installing the power supply with its fan f

64lnstallation GuideWe recommend at this point to start thinking about which fan size to use before installing the motherboard. If you are using an A

75lnstallation GuideSCREW CSCREW D6Insert the I/O shield included with your motherboard and then install the motherboard into the case.Установите загл

87lnstallation GuideWe recommend at this point to start thinking about routing the cables cleanly before connecting them to the motherboard, cables in